Project

General

Profile

Berkeley Sensor Deployments » History » Version 20

Version 19 (Ken Lutz, 09/11/2017 05:12 PM) → Version 20/23 (Nitesh Mor, 09/14/2017 02:54 PM)

{{toc}}

Note that log names are **lower case** and that some of the MACs are upper case. For example, a legitimate log name is:

~~~
edu.berkeley.eecs.swarmlab.device.c098e5900091
~~~

## Resources

* JSON file containing log names: http://swarmnuc1022.eecs.berkeley.edu/static/logs.json **The JSON file is more accurate than the text below**.
* Visualization tool: http://swarmnuc1022.eecs.berkeley.edu/static/

## Hints
* To test, use gdp-reader:

~~~
$PTII/vendors/gdp/gdp/apps/gdp-reader -s edu.berkeley.eecs.swarmlab.device.c098e5900091
~~~

* If you get a message about needing a secret key, then try updating and rebuilding the GDP

**i3 Network control**
Here are a few useful systemd commands for interaction with various components:

* Check service status. Generally, the number of child 'arm-coap-client' should be the same as the number of nodes (except the root node)
$ sudo service i3mote status

* start/stop/restart the service (Note that there is a 20 second startup delay to allow things to settle after a reboot)
$ sudo service i3mote <cmd>

* look at the logs of main wrapper
$ journalctl -u i3mote.service

# Berkeley Sensor Deployments

### Signposts

See https://github.com/lab11/signpost-software/blob/master/docs/DataSchemas.md

### BWRC Server Room

**Sensors and Gateways**

* BBB - UHKBBB004.eecs.berkeley.edu 128.32.63.176
* Rear Wall BLEE - C0:98:E5:30:00:36
* Mid Wall BLEE - C0:98:E5:30:00:5D
* Hot Aisle BLEE- C0:98:E5:30:00:54
* Lab Rear Wall BLEE - C0:98:E5:30:00:09
* BLINK - C0:98:E5:90:00:1E
* Power Blade - Utility power to sump pump - C0:98:E5:70:00:8F
* Power Blade - Utility power to Air Compressor - C0:98:E5:70:00::90
* USB Microphone - mounted on BBB

* I3 Sensor tag Mid Wall
* I3 Sensor tag, Lab rear wall

### BWRC Office Area

#### Sensors and Gateways

* Swarmnuc1002.eecs.berkeley.edu - on Ken's desk
* BLEE
~~ Main seating area - C0:98:E5:30:00:A5~~ Missing
- Conference Room , Rabaey Room - C0:98:E5:30:00:A3
- Admin Office - C0:98:E5:30:00:A4
- Conference Room - Brodersen room - C0:98:E5:30:00:A2
- Ken's Office - C0:98:E5:30:00:A1
- Brian Office above thermostat - C0:98:E5:30:00:A0
- Center of student seating area, above thermostat - C0:98:E5:30:00:37
* Blink
- Brodersen Conference Room C0:98:E5:90:00:87
- Rabaey Conference room - C0:98:E5:30:00:94

*I3 Mesh Network uhkbbb011 Host
* I3 Mesh root node
- EUI: 00-12-4b-00-0a-4a-b9-05 - Grad area, Pillar outside Kens office, sensor tag
- EUI: 00-12-4b-00-0a-63-0c-81 - Kens Office, on window, sensor tag
- EUI: 00-12-4b-00-0a-4a-58-02- Brians Office, over thermostat - Sensor tag
- EUI: 00-12-4b-00-0a-4b-38-83 - Kens Office, on desktop, sensor tag
- EUI: 00-12-4b-00-0a-55-c3-02 - Brodersen Conference Room, sensor tag
- EUI: 00-12-4b-00-0a-64-aa-04 - Rabaey Conference room, sensor tag
- EUI: 00-12-4b-00-0a-55-33-86 - Server Room mid wall, sensor tag
- EUI: 00-12-4b-00-07-91-3c-82 - Main Student area, on pillar, sensor tag, wall powered
- EUI: 00-12-4b-00-0a-4c-58-80 - Lab rear wall, sensor tag
- EUI: 00-12-4b-00-0b-23-45-83 - Server Room, Hot isle, sensor tag
- EUI: 00-12-4b-00-07-90-28-01 - Open forum, wall by south door, sensor tag, wall powered
- EUI: 00-12-4b-00-0c-2c-e3-86 - Optical lab wall, sensor tag, wall powered
- EUI: 00-12-4b-00-0c-31-b0-01 - Server room, rear wall, sensor tag
- EUI: 00-12-4b-00-0a-f7-da-83 - Rear of lab,over bench, i3 mote, energy harvesting
- EUI: 00-12-4b-00-0c-f7-d6-83 - Kens office window, i3 mote, energy harvesting

**Operational Notes**

* 6-17-16 2:59PM Repaired broken Blink in server room. Was reading all zero, now detecting movement correctly.
* 7/11/16 Fixed powerblade on air compressor - was installed backward. Data collected after 7/11 looks correct. Prior was in error. Note that energy accumulated goes to zero when powerblade was disconnected for inspection. Good marker.
* 7/14/16 9:29AM Correlated spike in temperature and humidity for a short period of time across all BLEES in the server room. Probably related to someone working in the room and having propped the door open.
* 7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
* 7/19/16 4:05 PM - 4:19PM: Put a cover over the Lab Rear wall BLEE causing the light level to go to zero. Temp and humidity are down as well.
* 7/19/16 4:20PM - 4:31PM: Put a cover over BLEE in server room, mid wall. Light level goes to zero, temp goes up. Other sensors in the server room do not show similar readings
* 7/25/16 - Added sensors and gateway to BWRC office area. New batteries
* 8/1/16 BBB004 down for maintenance 2-5pm.
* 8/8/2016 Replaced batteries in server room and Kens office
* 8/8/16 Removed test powerblade from air compressor outlet strip
* 8/26/16 9:40AM - 10:10am covered light sensor on BLEE in Ken's office - C0:98:E5:30:00:A1
* 8/26/16 11:42 - Covered light sensor on BLEE Center of student seating area, above thermostat - C0:98:E5:30:00:37
* 8/26/16 12:30 -12:45 (approx) increased humidity on BLEE Brian Office above thermostat - C0:98:E5:30:00:A0
* 8/26/16 2:41-2:47pm increased humidity on Rear Wall BLEE - C0:98:E5:30:00:36
* 9/16/16 11:41AM Replaced batteries in server room, Kens office, student area+
* 10/10/16 12:00 pm Senor tags deployed in server room and rear wall of lab
* 11/28/16 4:35 pm all batteries changed, BLE and Sensor tags
* 2/6/17 1:54 PM Sensor Tag Batteries replaced
* 2/12/17 I3 mesh node firmware updated to V3

### Cory Hall Swarm Lab and Immersion Room
**Servers and Sensors**

#### Immersion Room

* Primary projector PowerBlade (edu.berkeley.eecs.swarmlab.device.c098e570008d) ~~c0:98:e5:70:00:2b~~ c0:98:e5:70:00:8d **ATAG 00015**
* Secondary projector PowerBlade (edu.berkeley.eecs.swarmlab.device.c098e570008b) c0:98:e5:70:00:8b **ATAG 00016**
* Speaker Camera PowerBlade (edu.berkeley.eecs.swarmlab.device.c098e570008e) c0:98:e5:70:00:8e
* Audience Camera PowerBlade (edu.berkeley.eecs.swarmlab.device.c098e5700088) c0:98:e5:70:00:88
* BLEE, rear camera pillar (edu.berkeley.eecs.swarmlab.device.c098e5300003) c0:98:e5:30:00:03 **ATAG00008**
* Front wall adjacent to screen Blink (edu.berkeley.eecs.swarmlab.device.c098e590000a) c0:98:e5:90:00:0a **ATAG00010**
* UHKBBB001.eecs.berkeley.edu 128.32.33.236
* S/T EUI: 00-12-4b-00-07-91-0e-03, S/A 10 (Rear Pillar) **ATAG 00007**

Chair BLEES C0:98:E5:30:0: {58, 5c, 5F, 7a, 7b, 74, 75, 76, 77, 78}

#### Entrance Lobby

* Swarm Lab Inside Entrance Lobby
* Blink (edu.berkeley.eecs.swarmlab.device.c098e590000b) c0:98:e5:90:00:0b **ATAG 00001**
* BLEE (edu.berkeley.eecs.swarmlab.device.c098e530000a) c0:98:e5:30:00:0a **ATAG 00002**
* S/T EUI: 00-12-4b-00-07-90-75-83, S/A 8 (Pillar) **Atag 00000**
* S/T EUI: 00-12-4b-00-07-91-15-82, S/A 7 (entrance door) **ATAG 00003**

#### Office 490B

* UHKBBB002.eecs.berkeley.edu **ATAG 00004**
* ~~* S/T (Eng Version) EUI: 00-12-4b-00-0d-7d-fa-07, S/A 3 (Kens desktop)~~
* i3 Mote EUI 00-12-4b-00-f7-d9-87 - Energy Harvesting on window sill ** ATAG 00006**

#### Student Area
S/T EUI: 00-12-4b-00-0a-63-62-86, S/A 6 (Nitesh Desk) ** ATAG 00005**
S/T EUI: 00-12-4b-00-0a-55-3b-05, S/A 9 (Wall near Mark Desk) **ATAG 00009**
PowerBlade c0:98:e5:70:01:21 490 Printers **ATAG 00013**

#### Lab 490E - Boser Lab
i3 Mote EUI 00-12-4b-00-0a-f7-db-07 Lab Window, Energy Harvesting ** ATAG00011**

#### SwarmLab Kitchen
S/T EUI 00-12-4b-00-0a-63-02-06 Wall by window **ATAG 0012**
PowerBlade c0:98:e5:70:01:20 Coffee Maker ** ATAG 00014**

#### 4th floor Elevator Lobby

* Blink (edu.berkeley.eecs.swarmlab.device.c098e5900091) c0:98:e5:90:00:91
* SwarmBox swarmnuc1020.eecs.berkeley.edu

#### Exit Stair Door near 490

* Blink (edu.berkeley.eecs.swarmlab.device.c098e5900019) c0:98:e5:90:00:19

**Operational Notes**

- 7/12/16 2:59PM, powerblade on Speaker camera disconnected for inspection and reconnected. Note that accumulated energy goes to zero at this time.
- 7/13/16 10AM, powerblade on Immersion room primary projector re-installed, now in correct orientation. Readings from 10am on look correct.
- 7/14/16 9:22:58AM - Introduced an anomaly by heating the Immersion room BLEE located on the rear pillar with a hot air gun for about 4 min. Temperature and humidity impacted.
- 7/14/16 9:46AM - Speaker camera was left on since 7/12 2:26pm. Turned off at 7/14 9:46AM
- 7/15/16 - 9:40AM Primary projector powerblade seems to have a loose connection. No readings from 7/14 3:23PM until re-seated at 7/15 9:40AM
- 7/18/16 - 11:30AM BLEES installed on conference table chairs w/ new batteries
- 7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
- 7/19/16: Beaglebone gateway is got powered off. Last data collected was around 4:56PM. Restarted at 10:50PM
- 7/20/16: Rear Camera pillar BLEE - Battery replaced 3:26PM
- 7/26/16 Main projector power blade failed - replaced with new unit (new MAC)
- 8/1/16 BBB001 down for maintenance
- 8/8/16 Batteries replaced in all sensors except chairs
-10/10/16 Batteries replaced in all Mich sensors
- 10/12/16 Batteries replaced in all TI sensor tags
- 2/6/17 AA Batteries added to Sensor Tags
- 2/11/17 I3 mesh node firmware updated to V3

### Jacobs Hall

**Gateways**

- ~~ML-100 - swarmnuc1005.eecs.berkeley.edu B8:AE:ED:74:09:3D was port 10D-120C-03F10-D room 120~~
- BBB - uhkbbb005.eecs.berkeley.edu port 10D-332-04F17-D Room 332
- BBB uhkbbb006.eecs.berkeley.edu 54:4a:16:e0:8b:a1 10D-120C-03F10-D room 120
- BBB uhkbbb007.eecs.berkeley.edu 6c:ec:eb:5c:64:5b Room 10 10D-10B-02f16-D



#### Room 110

**Powerblades**

- c0:98:e5:70:01:13 Type A 3D printer 10026 room 110
- c0:98:e5:70:01:22
- c0:98:e5:70:01:23 Type A 3D printer 10047 room 110
- c0:98:e5:70:01:25
- c0:98:e5:70:01:26 Laser 2 room 110C
- c0:98:e5:70:01:27 Type A 3D printer 10097 room 110
- c0:98:e5:70:01:29 Type A 3D printer 10213 room 110
- c0:98:e5:70:00:e2 Laser 1 room 110C
- c0:98:e5:70:00:e5 Type A 3D printer 10035 room 110
- c0:98:e5:70:00:d3 Type A 3D printer 10098 room 110
- c0:98:e5:70:00:d7 Type A 3D printer 10025 room 110
- c0:98:e5:70:00:f7 Type A 3D printer 10038 room 110
- c0:98:e5:70:00:db - Type A 3D printer 10094 room 110
- c0:98:e5:70:01:31 Type A 3D printer 10034 room 110

**BLEE**

- c0:98:e5:30:00:57 room 110 by thermostst
- ~~c0:98:e5:30:00:55 c0:98:e5:30:00:55 check placement in room~~

room

#### Room 332

**PowerBlades**

- c0:98:e5:70:00:8a Carbon 3D printer room 332
- c0:98:e5:70:01:0c Dimension 2 (Bonnie) room 332
- c0:98:e5:70:01:2e Dimension 1 (Clyde) room 332

**BLEE**

- c0:98:e5:30:00:55 room 120
- c0:98:e5:30:00:50 room 332 Fortus 380 air exhaust vent
- c0:98:e5:30:00:51 room 332 center of room

**Blink**

- c0:98:e5:90:00:85 room 332
- c0:98:e5:90:00:94
- c0:98:e5:90:00:87

#### Room 10C
**Blink**

- c0:98:e5:90:00:81 - wood shop room 10C

**BLEE**

- c0:98:e5:30:00:62 room 10C Woodshop

**Operational Notes**

- Sensors installed, new batteries 7/15/16

### TAMU
edu.tamu.esp.Setup1c.device.*

**BLEE**
c098e530001d

**Blink**
c098e590010
c098e590011
c098e590012
c098e5900ac

**PowerBlade**
c098e5700028
c098e57000c4
c098e57000a8

There is also a Motion sensors placed on door. The format is JSON and provides three axis accelrometer, gyroscope, mangnometer and time stamp. The log for the sensor is:

edu.esp.Tamu.device.MotionNetBKP

**Notes**
The sensors have been placed in the graduate office space. The power blades are connected to power cords in use by students.