Wiki » History » Version 20

« Previous - Version 20/84 (diff) - Next » - Current version
Nitesh Mor, 07/19/2016 10:09 PM

GDP Deployment Notes

Data users email list created

If you would like to be notified of data anomalies or changes in the sensor actuator send an email to asking to be added to the email list,

log naming convention: Unless otherwise noted, the name of the corresponding logs are derived from the physical location (currently bwrc or swarmlab) and the lowercase MAC address:


For example, a sensor with MAC address C0:98:E5:30:00:03 in the immersion room (which is in swarmlab) will be named edu.berkeley.eecs.swarmlab.device.c098e5300003

BWRC Server Room

Sensors and Gateways
Rear Wall BLEE - C0:98:E5:30:00:36
Mid Wall BLEE - C0:98:E5:30:00:5D
Hot Aisle BLEE- C0:98:E5:30:00:54
BLINK - C0:98:E5:90:00:1E
Lab Rear Wall BLEE - C0:98:E5:30:00:09
Power Blade - Utility power to sump pump - C0:98:E5:70:00:8F
Power Blade - Utility power to Air Compressor - C0:98:E5:70:90
USB Microphone - mounted on BBB

Operational Notes
6-17-16 2:59PM Repaired broken Blink in server room. Was reading all zero, now detecting movement correctly.
7/11/16 Fixed powerblade on air compressor - was installed backward. Data collected after 7/11 looks correct. Prior was in error. Note that energy accumulated goes to zero when powerblade was disconnected for inspection. Good marker.
7/14/16 9:29AM Correlated spike in temperature and humidity for a short period of time across all BLEES in the server room. Probably related to someone working in the room and having propped the door open.
7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
7/19/16 - :BWRC BLEE, Lab Rear wall C0:98:E5:30:00:09
7/19/16 4:05 PM - 4:19PM

Put a cover over the BLEE causing the light level to go to zero. Temp and humidity are down as well.

7/19/16 4:20PM - 4:31PM
BWRC BLEE mid wall C0:98:E5:30:00:5D

Put a cover over BLEE in server room, mid wall. Light level goes to zero, temp goes up
Other sensors in the server room do not show similar readings

Cory Hall Swarm Lab and Immersion Room

Servers and Sensors
Immersion Room
Primary projector PowerBlade C0:98:E5:70:00:2B
Secondary projector PowerBlade C0:98:E5:70:00:8B
Speaker Camera PowerBlade C0:98:E5:70:00:8E
Audience Camera PowerBlade C0:98:E5:70:00:88
BLEE, rear camera pillar C0:98:E5:30:00:03
Front wall adjacent to screen Blink C0:98:E5:90:00:0A

Chair BLEES C0:98:E5:30:0: {58, 5c, 5F, 7a, 7b, 74, 75, 76, 77, 78}

Operational Notes
7/12/16 2:59PM, powerblade on Speaker camera disconnected for inspection and reconnected.
Note that accumulated energy goes to zero at this time.
7/13/16 10AM, powerblade on Immersion room primary projector re-installed, now in correct orientation. Readings from 10am on look correct.
7/14/16 9:22:58AM - Introduced an anomaly by heating the Immersion room BLEE located on the rear pillar with a hot air gun for about 4 min. Temperature and humidity impacted.
7/14/16 9:46AM - Speaker camera was left on since 7/12 2:26pm. Turned off at 7/14 9:46AM
7/15/16 - 9:40AM Primary projector powerblade seems to have a loose connection. No readings from 7/14 3:23PM until re-seated at 7/15 9:40AM
7/18/16 - 11:30AM BLEES installed on conference table chairs w/ new batteries
7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
7/19/16: Beaglebone gateway is either powered off, or got kicked out of the network. Last data collected was around 4:56PM.

Jacobs Hall

ML-100 -

Room 110

c0:98:e5:70:01:13 Type A 3D printer 10026 room 110
c0:98:e5:70:01:23 Type A 3D printer 10047 room 110
c0:98:e5:70:01:26 Laser 2 room 110C
c0:98:e5:70:01:27 Type A 3D printer 10097 room 110
c0:98:e5:70:01:29 Type A 3D printer 10213 room 110
c0:98:e5:70:00:e2 Laser 1 room 110C
c0:98:e5:70:00:e5 Type A 3D printer 10035 room 110
c0:98:e5:70:00:d3 Type A 3D printer 10098 room 110
c0:98:e5:70:00:d7 Type A 3D printer 10025 room 110
c0:98:e5:70:00:f7 Type A 3D printer 10038 room 110
c0:98:e5:70:00:db - Type A 3D printer 10094 room 110
c0:98:e5:70:01:31 Type A 3D printer 10034 room 110

c0:98:e5:30:00:57 room 110 by thermostst
c0:98:e5:30:00:62 room 10C Woodshop

Room 332

c0:98:e5:70:00:8a Carbon 3D printer room 332
c0:98:e5:70:01:0c Dimension 2 (Bonnie) room 332
c0:98:e5:70:01:2e Dimension 1 (Clyde) room 332

c0:98:e5:30:00:55 room 120
c0:98:e5:30:00:50 room 332 Fortus 380 air exhaust vent
c0:98:e5:30:00:51 room 332 center of room

c0:98:e5:90:00:85 room 332



Room 10C

c0:98:e5:90:00:81 - wood shop room 10C

Operational Notes
Sensors installed, new batteries 7/15/16