Project

General

Profile

Wiki » History » Version 35

Ken Lutz, 08/08/2016 02:16 PM

1 1 Ken Lutz
# GDP Deployment Notes
2 1 Ken Lutz
3 16 Ken Lutz
## Data users email list created
4 15 Ken Lutz
If you would like to be notified of data anomalies or changes in the sensor actuator send an email to lutz@berkeley.edu asking to be added to the email list, swarm-gdp-data-users@lists.eecs.berkeley.edu
5 15 Ken Lutz
6 13 Nitesh Mor
**log naming convention:** Unless otherwise noted, the name of the corresponding logs are derived from the physical location (currently `bwrc` or `swarmlab`) and the lowercase MAC address:
7 13 Nitesh Mor
8 13 Nitesh Mor
    edu.berkeley.eecs.<location>.device.<mac-addr>
9 13 Nitesh Mor
10 13 Nitesh Mor
For example, a sensor with MAC address `C0:98:E5:30:00:03` in the immersion room (which is in swarmlab) will be named `edu.berkeley.eecs.swarmlab.device.c098e5300003`
11 13 Nitesh Mor
12 2 Ken Lutz
## BWRC Server Room
13 3 Ken Lutz
**Sensors and Gateways**
14 3 Ken Lutz
BBB - UHKBBB004.eecs.berkeley.edu 128.32.63.176
15 3 Ken Lutz
Rear Wall BLEE - C0:98:E5:30:00:36 
16 3 Ken Lutz
Mid Wall BLEE - C0:98:E5:30:00:5D
17 3 Ken Lutz
Hot Aisle BLEE- C0:98:E5:30:00:54
18 3 Ken Lutz
BLINK - C0:98:E5:90:00:1E
19 3 Ken Lutz
Lab Rear Wall BLEE - C0:98:E5:30:00:09
20 3 Ken Lutz
Power Blade - Utility power to sump pump - C0:98:E5:70:00:8F
21 34 Ken Lutz
Power Blade - Utility power to Air Compressor - C0:98:E5:70:00::90
22 3 Ken Lutz
USB Microphone - mounted on BBB
23 3 Ken Lutz
24 23 Ken Lutz
## BWRC Office Area
25 23 Ken Lutz
**Sensors and Gateways**
26 23 Ken Lutz
Swarmnuc1002.eecs.berkeley.edu
27 24 Ken Lutz
**BLEE**
28 23 Ken Lutz
Main seating area - C0:98:E5:30:00:A5
29 23 Ken Lutz
Conference Room , Rabaey Room - C0:98:E5:30:00:A3
30 23 Ken Lutz
Admin Office - C0:98:E5:30:00:A4
31 23 Ken Lutz
Conference Room - Brodersen room - C0:98:E5:30:00:A2
32 23 Ken Lutz
Ken's Office  - C0:98:E5:30:00:A1
33 23 Ken Lutz
Brian Office above thermostat - C0:98:E5:30:00:A0
34 1 Ken Lutz
Center of student seating area, above thermostat - C0:98:E5:30:00:37
35 24 Ken Lutz
**Blink**
36 24 Ken Lutz
  Brodersen Conference Room C0:98:E5:90:00:87
37 24 Ken Lutz
Rabaey Conference room -  C0:98:E5:30:00:94
38 23 Ken Lutz
39 23 Ken Lutz
40 2 Ken Lutz
**Operational Notes**
41 2 Ken Lutz
6-17-16 2:59PM Repaired broken Blink in server room. Was reading all zero, now detecting movement correctly.
42 2 Ken Lutz
7/11/16 Fixed powerblade on air compressor - was installed backward. Data collected after 7/11 looks correct. Prior was in error. Note that energy accumulated goes to zero when powerblade was disconnected for inspection. Good marker. 
43 2 Ken Lutz
7/14/16 9:29AM Correlated spike in temperature and humidity for a short period of time across all BLEES in the server room. Probably related to someone working in the room and having propped the door open.
44 14 Nitesh Mor
7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway. 
45 17 Ken Lutz
7/19/16 - :BWRC BLEE, Lab Rear wall C0:98:E5:30:00:09
46 17 Ken Lutz
7/19/16 4:05 PM - 4:19PM
47 29 Ken Lutz
8/1/16 BBB004 down for maintenance 2-5pm.
48 17 Ken Lutz
49 17 Ken Lutz
Put a cover over the BLEE causing the light level to go to zero. Temp and humidity are down as well.
50 17 Ken Lutz
51 17 Ken Lutz
7/19/16 4:20PM - 4:31PM
52 17 Ken Lutz
BWRC  BLEE mid wall C0:98:E5:30:00:5D
53 17 Ken Lutz
54 17 Ken Lutz
Put a cover over BLEE in server room, mid wall. Light level goes to zero, temp goes up
55 17 Ken Lutz
Other sensors in the server room do not show similar readings
56 2 Ken Lutz
57 25 Ken Lutz
7/25/16 - Added sensors and gateway to BWRC office area. New batteries
58 25 Ken Lutz
59 2 Ken Lutz
## Cory Hall Swarm Lab and Immersion Room
60 11 Ken Lutz
**Servers and Sensors**
61 33 Ken Lutz
**Immersion Room**
62 26 Ken Lutz
Primary projector PowerBlade ~~C0:98:E5:70:00:2B~~ C0:98:E5:70:00:8D
63 11 Ken Lutz
Secondary projector PowerBlade C0:98:E5:70:00:8B
64 11 Ken Lutz
Speaker Camera PowerBlade C0:98:E5:70:00:8E
65 11 Ken Lutz
Audience Camera PowerBlade C0:98:E5:70:00:88
66 11 Ken Lutz
BLEE, rear camera pillar C0:98:E5:30:00:03
67 11 Ken Lutz
Front wall adjacent to screen Blink C0:98:E5:90:00:0A
68 11 Ken Lutz
UHKBBB001.eecs.berkeley.edu 128.32.33.236
69 11 Ken Lutz
70 1 Ken Lutz
Chair BLEES C0:98:E5:30:0:  {58, 5c, 5F, 7a, 7b, 74, 75, 76, 77, 78}
71 33 Ken Lutz
72 33 Ken Lutz
**Entrance Lobby**
73 33 Ken Lutz
74 33 Ken Lutz
Swarm Lab Inside Entrance Lobby
75 34 Ken Lutz
Blink C0:98:E5:90:00:0B
76 33 Ken Lutz
BLEE C0:98:E5:30:00:0A
77 33 Ken Lutz
78 33 Ken Lutz
**Office 490B**
79 33 Ken Lutz
UHKBBB002.eecs.berkeley.edu
80 33 Ken Lutz
81 33 Ken Lutz
**4th floor Elevator Lobby**
82 33 Ken Lutz
Blink C0:98:E5:90:00:91
83 33 Ken Lutz
SwarmBox swarmnuc1020.eecs.berkeley.edu
84 33 Ken Lutz
85 33 Ken Lutz
**Exit Stair Door near 490**
86 33 Ken Lutz
Blink C0:98:E5:90:00:19
87 33 Ken Lutz
88 33 Ken Lutz
89 11 Ken Lutz
90 12 Ken Lutz
91 2 Ken Lutz
**Operational Notes**
92 2 Ken Lutz
7/12/16 2:59PM, powerblade on Speaker camera disconnected for inspection and reconnected. 
93 2 Ken Lutz
Note that accumulated energy goes to zero at this time. 
94 2 Ken Lutz
7/13/16 10AM, powerblade on Immersion room primary projector re-installed, now in correct orientation. Readings from 10am on look correct.
95 2 Ken Lutz
7/14/16 9:22:58AM - Introduced an anomaly by heating the Immersion room BLEE located on the rear pillar with a hot air gun for about 4 min. Temperature and humidity impacted.
96 2 Ken Lutz
7/14/16 9:46AM - Speaker camera was left on since 7/12 2:26pm. Turned off at 7/14 9:46AM
97 1 Ken Lutz
7/15/16 - 9:40AM Primary projector powerblade seems to have a loose connection. No readings from 7/14 3:23PM until re-seated at 7/15 9:40AM
98 1 Ken Lutz
7/18/16 - 11:30AM BLEES installed on conference table chairs w/ new batteries
99 20 Nitesh Mor
7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
100 21 Nitesh Mor
7/19/16: Beaglebone gateway is got powered off. Last data collected was around 4:56PM. Restarted at 10:50PM
101 1 Ken Lutz
7/20/16: Rear Camera pillar BLEE - Battery replaced 3:26PM
102 26 Ken Lutz
7/26/16 Main projector power blade failed - replaced with new unit (new MAC)
103 29 Ken Lutz
8/1/16 BBB001 down for maintenance
104 35 Ken Lutz
8/8/16 Batteries replaced in all sensors except chairs
105 2 Ken Lutz
106 2 Ken Lutz
## Jacobs Hall
107 5 Ken Lutz
Gateways
108 31 Ken Lutz
~~ML-100 - swarmnuc1005.eecs.berkeley.edu B8:AE:ED:74:09:3D was port 10D-120C-03F10-D room 120~~
109 27 Ken Lutz
BBB - uhkbbb005.eecs.berkeley.edu port 10D-332-04F17-D Room 332
110 27 Ken Lutz
BBB uhkbbb006.eecs.berkeley.edu 54:4a:16:e0:8b:a1 10D-120C-03F10-D room 120
111 28 Ken Lutz
BBB uhkbbb007.eecs.berkeley.edu  6c:ec:eb:5c:64:5b Room 10 10D-10B-02f16-D
112 5 Ken Lutz
113 19 Ken Lutz
### Room 110
114 19 Ken Lutz
**Powerblades**
115 1 Ken Lutz
c0:98:e5:70:01:13 Type A 3D printer 10026	room 110
116 1 Ken Lutz
c0:98:e5:70:01:22
117 1 Ken Lutz
c0:98:e5:70:01:23 Type A 3D printer 10047	room 110
118 1 Ken Lutz
c0:98:e5:70:01:25
119 1 Ken Lutz
c0:98:e5:70:01:26 Laser 2                                room 110C
120 1 Ken Lutz
c0:98:e5:70:01:27 Type A 3D printer 10097	room 110
121 1 Ken Lutz
c0:98:e5:70:01:29 Type A 3D printer 10213	room 110
122 19 Ken Lutz
c0:98:e5:70:00:e2 Laser 1	                                room 110C
123 19 Ken Lutz
c0:98:e5:70:00:e5 Type A 3D printer 10035	room 110
124 19 Ken Lutz
c0:98:e5:70:00:d3 Type A 3D printer 10098	room 110
125 19 Ken Lutz
c0:98:e5:70:00:d7 Type A 3D printer 10025	room 110
126 19 Ken Lutz
c0:98:e5:70:00:f7 Type A 3D printer 10038	room 110
127 19 Ken Lutz
c0:98:e5:70:00:db - Type A 3D printer 10094 room 110
128 19 Ken Lutz
c0:98:e5:70:01:31 Type A 3D printer 10034	room 110	
129 19 Ken Lutz
**
130 19 Ken Lutz
BLEE**
131 1 Ken Lutz
c0:98:e5:30:00:57 room 110 by thermostst
132 34 Ken Lutz
c0:98:e5:30:00:55  check placement in room
133 19 Ken Lutz
134 34 Ken Lutz
135 19 Ken Lutz
### Room 332
136 19 Ken Lutz
137 19 Ken Lutz
**PowerBlades**
138 19 Ken Lutz
c0:98:e5:70:00:8a Carbon 3D printer              room 332
139 18 Ken Lutz
c0:98:e5:70:01:0c Dimension 2 (Bonnie)	room 332
140 1 Ken Lutz
c0:98:e5:70:01:2e Dimension 1 (Clyde)         room 332
141 4 Ken Lutz
142 19 Ken Lutz
**BLEE**
143 32 Ken Lutz
144 1 Ken Lutz
c0:98:e5:30:00:55 room 120
145 4 Ken Lutz
c0:98:e5:30:00:50 room 332 Fortus 380 air exhaust vent
146 4 Ken Lutz
c0:98:e5:30:00:51 room 332 center of room
147 7 Ken Lutz
148 19 Ken Lutz
**Blink**
149 19 Ken Lutz
c0:98:e5:90:00:85 room 332
150 19 Ken Lutz
151 32 Ken Lutz
152 32 Ken Lutz
153 4 Ken Lutz
c0:98:e5:90:00:94
154 32 Ken Lutz
155 19 Ken Lutz
156 4 Ken Lutz
c0:98:e5:90:00:87
157 19 Ken Lutz
158 1 Ken Lutz
### Room 10C
159 1 Ken Lutz
**Blink**
160 19 Ken Lutz
c0:98:e5:90:00:81 - wood shop room 10C
161 34 Ken Lutz
**BLEE**
162 34 Ken Lutz
c0:98:e5:30:00:62 room 10C Woodshop
163 4 Ken Lutz
164 4 Ken Lutz
165 2 Ken Lutz
**Operational Notes**
166 4 Ken Lutz
Sensors installed, new batteries 7/15/16
167 30 Eric Allman
168 30 Eric Allman
169 30 Eric Allman
## Configuring Gateways
170 30 Eric Allman
171 30 Eric Allman
See [[Configuring Gateways]] for information about setting up gateway hosts (typically either BBBs or SwarmBoxes).