Others » GDP Sensor and Actuator Deployments

# GDP Deployment Notes

## Data users email list created

If you would like to be notified of data anomalies or changes in the sensor actuator send an email to lutz@berkeley.edu asking to be added to the email list, swarm-gdp-data-users@lists.eecs.berkeley.edu

## Conventions

Unless otherwise noted, the name of the corresponding logs are derived from the physical location (currently `bwrc` or `swarmlab`) and the lowercase MAC address:

    edu.berkeley.eecs.<location>.device.<mac-addr>

For example, a sensor with MAC address `C0:98:E5:30:00:03` in the immersion room (which is in swarmlab) will be named `edu.berkeley.eecs.swarmlab.device.c098e5300003`

## Provisioning

See [[Provisioning Sensors]] for instructions on how to add new sensors.

## Deployments

### BWRC Server Room

**Sensors and Gateways**

BBB - UHKBBB004.eecs.berkeley.edu 128.32.63.176

Rear Wall BLEE - C0:98:E5:30:00:36 

Mid Wall BLEE - C0:98:E5:30:00:5D

Hot Aisle BLEE- C0:98:E5:30:00:54

BLINK - C0:98:E5:90:00:1E

Lab Rear Wall BLEE - C0:98:E5:30:00:09

Power Blade - Utility power to sump pump - C0:98:E5:70:00:8F

Power Blade - Utility power to Air Compressor - C0:98:E5:70:00::90

USB Microphone - mounted on BBB

### BWRC Office Area

**Sensors and Gateways**

Swarmnuc1002.eecs.berkeley.edu

**BLEE**

Main seating area - C0:98:E5:30:00:A5

Conference Room , Rabaey Room - C0:98:E5:30:00:A3

Admin Office - C0:98:E5:30:00:A4

Conference Room - Brodersen room - C0:98:E5:30:00:A2

Ken's Office  - C0:98:E5:30:00:A1

Brian Office above thermostat - C0:98:E5:30:00:A0

Center of student seating area, above thermostat - C0:98:E5:30:00:37

**Blink**

  Brodersen Conference Room C0:98:E5:90:00:87

Rabaey Conference room -  C0:98:E5:30:00:94

**Operational Notes**

6-17-16 2:59PM Repaired broken Blink in server room. Was reading all zero, now detecting movement correctly.

7/11/16 Fixed powerblade on air compressor - was installed backward. Data collected after 7/11 looks correct. Prior was in error. Note that energy accumulated goes to zero when powerblade was disconnected for inspection. Good marker. 

7/14/16 9:29AM Correlated spike in temperature and humidity for a short period of time across all BLEES in the server room. Probably related to someone working in the room and having propped the door open.

7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway. 

7/19/16 - :BWRC BLEE, Lab Rear wall C0:98:E5:30:00:09

7/19/16 4:05 PM - 4:19PM

8/1/16 BBB004 down for maintenance 2-5pm.

Put a cover over the BLEE causing the light level to go to zero. Temp and humidity are down as well.

7/19/16 4:20PM - 4:31PM

BWRC  BLEE mid wall C0:98:E5:30:00:5D

Put a cover over BLEE in server room, mid wall. Light level goes to zero, temp goes up

Other sensors in the server room do not show similar readings

7/25/16 - Added sensors and gateway to BWRC office area. New batteries

8/8/2016 Replaced batteries in server room  and Kens office

8/8/16 Removed test powerblade from air compressor outlet strip

### Cory Hall Swarm Lab and Immersion Room

**Servers and Sensors**

#### Immersion Room

Primary projector PowerBlade ~~C0:98:E5:70:00:2B~~ C0:98:E5:70:00:8D

Secondary projector PowerBlade C0:98:E5:70:00:8B

Speaker Camera PowerBlade C0:98:E5:70:00:8E

Audience Camera PowerBlade C0:98:E5:70:00:88

BLEE, rear camera pillar C0:98:E5:30:00:03

Front wall adjacent to screen Blink C0:98:E5:90:00:0A

UHKBBB001.eecs.berkeley.edu 128.32.33.236

Chair BLEES C0:98:E5:30:0:  {58, 5c, 5F, 7a, 7b, 74, 75, 76, 77, 78}

#### Entrance Lobby

Swarm Lab Inside Entrance Lobby

Blink C0:98:E5:90:00:0B

BLEE C0:98:E5:30:00:0A

#### Office 490B

UHKBBB002.eecs.berkeley.edu

#### 4th floor Elevator Lobby

Blink C0:98:E5:90:00:91

SwarmBox swarmnuc1020.eecs.berkeley.edu

#### Exit Stair Door near 490

Blink C0:98:E5:90:00:19

**Operational Notes**

7/12/16 2:59PM, powerblade on Speaker camera disconnected for inspection and reconnected. 

Note that accumulated energy goes to zero at this time. 

7/13/16 10AM, powerblade on Immersion room primary projector re-installed, now in correct orientation. Readings from 10am on look correct.

7/14/16 9:22:58AM - Introduced an anomaly by heating the Immersion room BLEE located on the rear pillar with a hot air gun for about 4 min. Temperature and humidity impacted.

7/14/16 9:46AM - Speaker camera was left on since 7/12 2:26pm. Turned off at 7/14 9:46AM

7/15/16 - 9:40AM Primary projector powerblade seems to have a loose connection. No readings from 7/14 3:23PM until re-seated at 7/15 9:40AM

7/18/16 - 11:30AM BLEES installed on conference table chairs w/ new batteries

7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.

7/19/16: Beaglebone gateway is got powered off. Last data collected was around 4:56PM. Restarted at 10:50PM

7/20/16: Rear Camera pillar BLEE - Battery replaced 3:26PM

7/26/16 Main projector power blade failed - replaced with new unit (new MAC)

8/1/16 BBB001 down for maintenance

8/8/16 Batteries replaced in all sensors except chairs

### Jacobs Hall

**Gateways**

~~ML-100 - swarmnuc1005.eecs.berkeley.edu B8:AE:ED:74:09:3D was port 10D-120C-03F10-D room 120~~

BBB - uhkbbb005.eecs.berkeley.edu port 10D-332-04F17-D Room 332

BBB uhkbbb006.eecs.berkeley.edu 54:4a:16:e0:8b:a1 10D-120C-03F10-D room 120

BBB uhkbbb007.eecs.berkeley.edu  6c:ec:eb:5c:64:5b Room 10 10D-10B-02f16-D

#### Room 110

**Powerblades**

c0:98:e5:70:01:13 Type A 3D printer 10026	room 110

c0:98:e5:70:01:22

c0:98:e5:70:01:23 Type A 3D printer 10047	room 110

c0:98:e5:70:01:25

c0:98:e5:70:01:26 Laser 2                                room 110C

c0:98:e5:70:01:27 Type A 3D printer 10097	room 110

c0:98:e5:70:01:29 Type A 3D printer 10213	room 110

c0:98:e5:70:00:e2 Laser 1	                                room 110C

c0:98:e5:70:00:e5 Type A 3D printer 10035	room 110

c0:98:e5:70:00:d3 Type A 3D printer 10098	room 110

c0:98:e5:70:00:d7 Type A 3D printer 10025	room 110

c0:98:e5:70:00:f7 Type A 3D printer 10038	room 110

c0:98:e5:70:00:db - Type A 3D printer 10094 room 110

c0:98:e5:70:01:31 Type A 3D printer 10034	room 110	

**BLEE**

c0:98:e5:30:00:57 room 110 by thermostst

c0:98:e5:30:00:55  check placement in room

#### Room 332

**PowerBlades**

c0:98:e5:70:00:8a Carbon 3D printer              room 332

c0:98:e5:70:01:0c Dimension 2 (Bonnie)	room 332

c0:98:e5:70:01:2e Dimension 1 (Clyde)         room 332

**BLEE**

c0:98:e5:30:00:55 room 120

c0:98:e5:30:00:50 room 332 Fortus 380 air exhaust vent

c0:98:e5:30:00:51 room 332 center of room

**Blink**

c0:98:e5:90:00:85 room 332

c0:98:e5:90:00:94

c0:98:e5:90:00:87

#### Room 10C

**Blink**

c0:98:e5:90:00:81 - wood shop room 10C

**BLEE**

c0:98:e5:30:00:62 room 10C Woodshop

**Operational Notes**

Sensors installed, new batteries 7/15/16

### Unassigned BBB Ready for deployment

UHKBBB008.eecs.berkeley.edu  b0:d5:cc:83:0b:01

UHKBBB009.eecs.berkeley.edu  88:c2:55:83:6c:29

## Configuring Gateways

See [[Configuring Gateways]] for information about setting up gateway hosts (typically either BBBs or SwarmBoxes).