Project

General

Profile

Wiki » History » Version 41

Nitesh Mor, 08/25/2016 09:17 AM

1 39 Nitesh Mor
{{toc}}
2 39 Nitesh Mor
3 1 Ken Lutz
# GDP Deployment Notes
4 1 Ken Lutz
5 16 Ken Lutz
## Data users email list created
6 15 Ken Lutz
If you would like to be notified of data anomalies or changes in the sensor actuator send an email to lutz@berkeley.edu asking to be added to the email list, swarm-gdp-data-users@lists.eecs.berkeley.edu
7 15 Ken Lutz
8 38 Eric Allman
## Conventions
9 38 Eric Allman
Unless otherwise noted, the name of the corresponding logs are derived from the physical location (currently `bwrc` or `swarmlab`) and the lowercase MAC address:
10 13 Nitesh Mor
11 13 Nitesh Mor
    edu.berkeley.eecs.<location>.device.<mac-addr>
12 13 Nitesh Mor
13 1 Ken Lutz
For example, a sensor with MAC address `C0:98:E5:30:00:03` in the immersion room (which is in swarmlab) will be named `edu.berkeley.eecs.swarmlab.device.c098e5300003`
14 1 Ken Lutz
15 38 Eric Allman
## Provisioning
16 38 Eric Allman
See [[Provisioning Sensors]] for instructions on how to add new sensors.
17 38 Eric Allman
18 39 Nitesh Mor
## Configuring Gateways
19 39 Nitesh Mor
See [[Configuring Gateways]] for information about setting up gateway hosts (typically either BBBs or SwarmBoxes).
20 39 Nitesh Mor
21 38 Eric Allman
## Deployments
22 38 Eric Allman
23 38 Eric Allman
### BWRC Server Room
24 40 Nitesh Mor
25 1 Ken Lutz
**Sensors and Gateways**
26 41 Nitesh Mor
27 40 Nitesh Mor
* BBB - UHKBBB004.eecs.berkeley.edu 128.32.63.176
28 40 Nitesh Mor
* Rear Wall BLEE - C0:98:E5:30:00:36 
29 40 Nitesh Mor
* Mid Wall BLEE - C0:98:E5:30:00:5D
30 40 Nitesh Mor
* Hot Aisle BLEE- C0:98:E5:30:00:54
31 40 Nitesh Mor
* Lab Rear Wall BLEE - C0:98:E5:30:00:09
32 40 Nitesh Mor
* BLINK - C0:98:E5:90:00:1E
33 40 Nitesh Mor
* Power Blade - Utility power to sump pump - C0:98:E5:70:00:8F
34 40 Nitesh Mor
* Power Blade - Utility power to Air Compressor - C0:98:E5:70:00::90
35 40 Nitesh Mor
* USB Microphone - mounted on BBB
36 23 Ken Lutz
37 23 Ken Lutz
### BWRC Office Area
38 23 Ken Lutz
39 40 Nitesh Mor
#### Sensors and Gateways**
40 23 Ken Lutz
41 40 Nitesh Mor
* Swarmnuc1002.eecs.berkeley.edu
42 40 Nitesh Mor
* BLEE
43 40 Nitesh Mor
    - Main seating area - C0:98:E5:30:00:A5
44 40 Nitesh Mor
    - Conference Room , Rabaey Room - C0:98:E5:30:00:A3
45 40 Nitesh Mor
    - Admin Office - C0:98:E5:30:00:A4
46 40 Nitesh Mor
    - Conference Room - Brodersen room - C0:98:E5:30:00:A2
47 40 Nitesh Mor
    - Ken's Office  - C0:98:E5:30:00:A1
48 40 Nitesh Mor
    - Brian Office above thermostat - C0:98:E5:30:00:A0
49 40 Nitesh Mor
    - Center of student seating area, above thermostat - C0:98:E5:30:00:37
50 40 Nitesh Mor
* Blink
51 40 Nitesh Mor
    - Brodersen Conference Room C0:98:E5:90:00:87
52 40 Nitesh Mor
    - Rabaey Conference room -  C0:98:E5:30:00:94
53 17 Ken Lutz
54 29 Ken Lutz
55 40 Nitesh Mor
**Operational Notes**
56 17 Ken Lutz
57 40 Nitesh Mor
* 6-17-16 2:59PM Repaired broken Blink in server room. Was reading all zero, now detecting movement correctly.
58 40 Nitesh Mor
* 7/11/16 Fixed powerblade on air compressor - was installed backward. Data collected after 7/11 looks correct. Prior was in error. Note that energy accumulated goes to zero when powerblade was disconnected for inspection. Good marker. 
59 40 Nitesh Mor
* 7/14/16 9:29AM Correlated spike in temperature and humidity for a short period of time across all BLEES in the server room. Probably related to someone working in the room and having propped the door open.
60 40 Nitesh Mor
* 7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway. 
61 40 Nitesh Mor
* 7/19/16 4:05 PM - 4:19PM: Put a cover over the Lab Rear wall BLEE causing the light level to go to zero. Temp and humidity are down as well.
62 40 Nitesh Mor
* 7/19/16 4:20PM - 4:31PM: Put a cover over BLEE in server room, mid wall. Light level goes to zero, temp goes up. Other sensors in the server room do not show similar readings
63 40 Nitesh Mor
* 7/25/16 - Added sensors and gateway to BWRC office area. New batteries
64 40 Nitesh Mor
* 8/1/16 BBB004 down for maintenance 2-5pm.
65 40 Nitesh Mor
* 8/8/2016 Replaced batteries in server room  and Kens office
66 40 Nitesh Mor
* 8/8/16 Removed test powerblade from air compressor outlet strip
67 36 Ken Lutz
68 38 Eric Allman
### Cory Hall Swarm Lab and Immersion Room
69 2 Ken Lutz
**Servers and Sensors**
70 38 Eric Allman
71 38 Eric Allman
#### Immersion Room
72 11 Ken Lutz
Primary projector PowerBlade ~~C0:98:E5:70:00:2B~~ C0:98:E5:70:00:8D
73 11 Ken Lutz
Secondary projector PowerBlade C0:98:E5:70:00:8B
74 11 Ken Lutz
Speaker Camera PowerBlade C0:98:E5:70:00:8E
75 11 Ken Lutz
Audience Camera PowerBlade C0:98:E5:70:00:88
76 1 Ken Lutz
BLEE, rear camera pillar C0:98:E5:30:00:03
77 11 Ken Lutz
Front wall adjacent to screen Blink C0:98:E5:90:00:0A
78 1 Ken Lutz
UHKBBB001.eecs.berkeley.edu 128.32.33.236
79 33 Ken Lutz
80 33 Ken Lutz
Chair BLEES C0:98:E5:30:0:  {58, 5c, 5F, 7a, 7b, 74, 75, 76, 77, 78}
81 1 Ken Lutz
82 38 Eric Allman
#### Entrance Lobby
83 1 Ken Lutz
84 34 Ken Lutz
Swarm Lab Inside Entrance Lobby
85 33 Ken Lutz
Blink C0:98:E5:90:00:0B
86 1 Ken Lutz
BLEE C0:98:E5:30:00:0A
87 33 Ken Lutz
88 38 Eric Allman
#### Office 490B
89 33 Ken Lutz
UHKBBB002.eecs.berkeley.edu
90 33 Ken Lutz
91 38 Eric Allman
#### 4th floor Elevator Lobby
92 33 Ken Lutz
Blink C0:98:E5:90:00:91
93 33 Ken Lutz
SwarmBox swarmnuc1020.eecs.berkeley.edu
94 33 Ken Lutz
95 33 Ken Lutz
#### Exit Stair Door near 490
96 33 Ken Lutz
Blink C0:98:E5:90:00:19
97 11 Ken Lutz
98 2 Ken Lutz
99 2 Ken Lutz
**Operational Notes**
100 2 Ken Lutz
7/12/16 2:59PM, powerblade on Speaker camera disconnected for inspection and reconnected. 
101 2 Ken Lutz
Note that accumulated energy goes to zero at this time. 
102 2 Ken Lutz
7/13/16 10AM, powerblade on Immersion room primary projector re-installed, now in correct orientation. Readings from 10am on look correct.
103 1 Ken Lutz
7/14/16 9:22:58AM - Introduced an anomaly by heating the Immersion room BLEE located on the rear pillar with a hot air gun for about 4 min. Temperature and humidity impacted.
104 1 Ken Lutz
7/14/16 9:46AM - Speaker camera was left on since 7/12 2:26pm. Turned off at 7/14 9:46AM
105 1 Ken Lutz
7/15/16 - 9:40AM Primary projector powerblade seems to have a loose connection. No readings from 7/14 3:23PM until re-seated at 7/15 9:40AM
106 20 Nitesh Mor
7/18/16 - 11:30AM BLEES installed on conference table chairs w/ new batteries
107 21 Nitesh Mor
7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
108 1 Ken Lutz
7/19/16: Beaglebone gateway is got powered off. Last data collected was around 4:56PM. Restarted at 10:50PM
109 1 Ken Lutz
7/20/16: Rear Camera pillar BLEE - Battery replaced 3:26PM
110 26 Ken Lutz
7/26/16 Main projector power blade failed - replaced with new unit (new MAC)
111 29 Ken Lutz
8/1/16 BBB001 down for maintenance
112 35 Ken Lutz
8/8/16 Batteries replaced in all sensors except chairs
113 2 Ken Lutz
114 38 Eric Allman
### Jacobs Hall
115 38 Eric Allman
**Gateways**
116 31 Ken Lutz
~~ML-100 - swarmnuc1005.eecs.berkeley.edu B8:AE:ED:74:09:3D was port 10D-120C-03F10-D room 120~~
117 27 Ken Lutz
BBB - uhkbbb005.eecs.berkeley.edu port 10D-332-04F17-D Room 332
118 5 Ken Lutz
BBB uhkbbb006.eecs.berkeley.edu 54:4a:16:e0:8b:a1 10D-120C-03F10-D room 120
119 19 Ken Lutz
BBB uhkbbb007.eecs.berkeley.edu  6c:ec:eb:5c:64:5b Room 10 10D-10B-02f16-D
120 19 Ken Lutz
121 38 Eric Allman
#### Room 110
122 1 Ken Lutz
**Powerblades**
123 1 Ken Lutz
c0:98:e5:70:01:13 Type A 3D printer 10026	room 110
124 1 Ken Lutz
c0:98:e5:70:01:22
125 1 Ken Lutz
c0:98:e5:70:01:23 Type A 3D printer 10047	room 110
126 1 Ken Lutz
c0:98:e5:70:01:25
127 1 Ken Lutz
c0:98:e5:70:01:26 Laser 2                                room 110C
128 1 Ken Lutz
c0:98:e5:70:01:27 Type A 3D printer 10097	room 110
129 1 Ken Lutz
c0:98:e5:70:01:29 Type A 3D printer 10213	room 110
130 19 Ken Lutz
c0:98:e5:70:00:e2 Laser 1	                                room 110C
131 19 Ken Lutz
c0:98:e5:70:00:e5 Type A 3D printer 10035	room 110
132 19 Ken Lutz
c0:98:e5:70:00:d3 Type A 3D printer 10098	room 110
133 19 Ken Lutz
c0:98:e5:70:00:d7 Type A 3D printer 10025	room 110
134 19 Ken Lutz
c0:98:e5:70:00:f7 Type A 3D printer 10038	room 110
135 19 Ken Lutz
c0:98:e5:70:00:db - Type A 3D printer 10094 room 110
136 19 Ken Lutz
c0:98:e5:70:01:31 Type A 3D printer 10034	room 110	
137 38 Eric Allman
138 38 Eric Allman
**BLEE**
139 1 Ken Lutz
c0:98:e5:30:00:57 room 110 by thermostst
140 34 Ken Lutz
c0:98:e5:30:00:55  check placement in room
141 19 Ken Lutz
142 34 Ken Lutz
143 38 Eric Allman
#### Room 332
144 19 Ken Lutz
145 19 Ken Lutz
**PowerBlades**
146 18 Ken Lutz
c0:98:e5:70:00:8a Carbon 3D printer              room 332
147 1 Ken Lutz
c0:98:e5:70:01:0c Dimension 2 (Bonnie)	room 332
148 4 Ken Lutz
c0:98:e5:70:01:2e Dimension 1 (Clyde)         room 332
149 19 Ken Lutz
150 1 Ken Lutz
**BLEE**
151 32 Ken Lutz
152 1 Ken Lutz
c0:98:e5:30:00:55 room 120
153 19 Ken Lutz
c0:98:e5:30:00:50 room 332 Fortus 380 air exhaust vent
154 32 Ken Lutz
c0:98:e5:30:00:51 room 332 center of room
155 32 Ken Lutz
156 4 Ken Lutz
**Blink**
157 32 Ken Lutz
c0:98:e5:90:00:85 room 332
158 19 Ken Lutz
c0:98:e5:90:00:94
159 4 Ken Lutz
c0:98:e5:90:00:87
160 19 Ken Lutz
161 38 Eric Allman
#### Room 10C
162 1 Ken Lutz
**Blink**
163 19 Ken Lutz
c0:98:e5:90:00:81 - wood shop room 10C
164 34 Ken Lutz
**BLEE**
165 34 Ken Lutz
c0:98:e5:30:00:62 room 10C Woodshop
166 4 Ken Lutz
167 4 Ken Lutz
168 2 Ken Lutz
**Operational Notes**
169 37 Ken Lutz
Sensors installed, new batteries 7/15/16
170 30 Eric Allman
171 30 Eric Allman
### Unassigned BBB Ready for deployment
172 30 Eric Allman
UHKBBB008.eecs.berkeley.edu  b0:d5:cc:83:0b:01
173 30 Eric Allman
UHKBBB009.eecs.berkeley.edu  88:c2:55:83:6c:29