Project

General

Profile

Wiki » History » Version 45

Nitesh Mor, 08/25/2016 09:20 AM

1 39 Nitesh Mor
{{toc}}
2 39 Nitesh Mor
3 1 Ken Lutz
# GDP Deployment Notes
4 1 Ken Lutz
5 16 Ken Lutz
## Data users email list created
6 15 Ken Lutz
If you would like to be notified of data anomalies or changes in the sensor actuator send an email to lutz@berkeley.edu asking to be added to the email list, swarm-gdp-data-users@lists.eecs.berkeley.edu
7 15 Ken Lutz
8 38 Eric Allman
## Conventions
9 38 Eric Allman
Unless otherwise noted, the name of the corresponding logs are derived from the physical location (currently `bwrc` or `swarmlab`) and the lowercase MAC address:
10 13 Nitesh Mor
11 13 Nitesh Mor
    edu.berkeley.eecs.<location>.device.<mac-addr>
12 13 Nitesh Mor
13 1 Ken Lutz
For example, a sensor with MAC address `C0:98:E5:30:00:03` in the immersion room (which is in swarmlab) will be named `edu.berkeley.eecs.swarmlab.device.c098e5300003`
14 1 Ken Lutz
15 38 Eric Allman
## Provisioning
16 38 Eric Allman
See [[Provisioning Sensors]] for instructions on how to add new sensors.
17 38 Eric Allman
18 39 Nitesh Mor
## Configuring Gateways
19 39 Nitesh Mor
See [[Configuring Gateways]] for information about setting up gateway hosts (typically either BBBs or SwarmBoxes).
20 39 Nitesh Mor
21 38 Eric Allman
## Deployments
22 38 Eric Allman
23 38 Eric Allman
### BWRC Server Room
24 40 Nitesh Mor
25 1 Ken Lutz
**Sensors and Gateways**
26 41 Nitesh Mor
27 40 Nitesh Mor
* BBB - UHKBBB004.eecs.berkeley.edu 128.32.63.176
28 40 Nitesh Mor
* Rear Wall BLEE - C0:98:E5:30:00:36 
29 40 Nitesh Mor
* Mid Wall BLEE - C0:98:E5:30:00:5D
30 40 Nitesh Mor
* Hot Aisle BLEE- C0:98:E5:30:00:54
31 40 Nitesh Mor
* Lab Rear Wall BLEE - C0:98:E5:30:00:09
32 40 Nitesh Mor
* BLINK - C0:98:E5:90:00:1E
33 40 Nitesh Mor
* Power Blade - Utility power to sump pump - C0:98:E5:70:00:8F
34 40 Nitesh Mor
* Power Blade - Utility power to Air Compressor - C0:98:E5:70:00::90
35 40 Nitesh Mor
* USB Microphone - mounted on BBB
36 23 Ken Lutz
37 23 Ken Lutz
### BWRC Office Area
38 23 Ken Lutz
39 42 Nitesh Mor
#### Sensors and Gateways
40 23 Ken Lutz
41 40 Nitesh Mor
* Swarmnuc1002.eecs.berkeley.edu
42 40 Nitesh Mor
* BLEE
43 40 Nitesh Mor
    - Main seating area - C0:98:E5:30:00:A5
44 40 Nitesh Mor
    - Conference Room , Rabaey Room - C0:98:E5:30:00:A3
45 40 Nitesh Mor
    - Admin Office - C0:98:E5:30:00:A4
46 40 Nitesh Mor
    - Conference Room - Brodersen room - C0:98:E5:30:00:A2
47 40 Nitesh Mor
    - Ken's Office  - C0:98:E5:30:00:A1
48 40 Nitesh Mor
    - Brian Office above thermostat - C0:98:E5:30:00:A0
49 40 Nitesh Mor
    - Center of student seating area, above thermostat - C0:98:E5:30:00:37
50 40 Nitesh Mor
* Blink
51 40 Nitesh Mor
    - Brodersen Conference Room C0:98:E5:90:00:87
52 40 Nitesh Mor
    - Rabaey Conference room -  C0:98:E5:30:00:94
53 17 Ken Lutz
54 29 Ken Lutz
55 40 Nitesh Mor
**Operational Notes**
56 17 Ken Lutz
57 40 Nitesh Mor
* 6-17-16 2:59PM Repaired broken Blink in server room. Was reading all zero, now detecting movement correctly.
58 40 Nitesh Mor
* 7/11/16 Fixed powerblade on air compressor - was installed backward. Data collected after 7/11 looks correct. Prior was in error. Note that energy accumulated goes to zero when powerblade was disconnected for inspection. Good marker. 
59 40 Nitesh Mor
* 7/14/16 9:29AM Correlated spike in temperature and humidity for a short period of time across all BLEES in the server room. Probably related to someone working in the room and having propped the door open.
60 40 Nitesh Mor
* 7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway. 
61 40 Nitesh Mor
* 7/19/16 4:05 PM - 4:19PM: Put a cover over the Lab Rear wall BLEE causing the light level to go to zero. Temp and humidity are down as well.
62 40 Nitesh Mor
* 7/19/16 4:20PM - 4:31PM: Put a cover over BLEE in server room, mid wall. Light level goes to zero, temp goes up. Other sensors in the server room do not show similar readings
63 40 Nitesh Mor
* 7/25/16 - Added sensors and gateway to BWRC office area. New batteries
64 40 Nitesh Mor
* 8/1/16 BBB004 down for maintenance 2-5pm.
65 40 Nitesh Mor
* 8/8/2016 Replaced batteries in server room  and Kens office
66 40 Nitesh Mor
* 8/8/16 Removed test powerblade from air compressor outlet strip
67 36 Ken Lutz
68 38 Eric Allman
### Cory Hall Swarm Lab and Immersion Room
69 2 Ken Lutz
**Servers and Sensors**
70 38 Eric Allman
71 38 Eric Allman
#### Immersion Room
72 43 Nitesh Mor
73 43 Nitesh Mor
* Primary projector PowerBlade ~~C0:98:E5:70:00:2B~~ C0:98:E5:70:00:8D
74 43 Nitesh Mor
* Secondary projector PowerBlade C0:98:E5:70:00:8B
75 43 Nitesh Mor
* Speaker Camera PowerBlade C0:98:E5:70:00:8E
76 43 Nitesh Mor
* Audience Camera PowerBlade C0:98:E5:70:00:88
77 43 Nitesh Mor
* BLEE, rear camera pillar C0:98:E5:30:00:03
78 43 Nitesh Mor
* Front wall adjacent to screen Blink C0:98:E5:90:00:0A
79 43 Nitesh Mor
* UHKBBB001.eecs.berkeley.edu 128.32.33.236
80 33 Ken Lutz
81 33 Ken Lutz
Chair BLEES C0:98:E5:30:0:  {58, 5c, 5F, 7a, 7b, 74, 75, 76, 77, 78}
82 1 Ken Lutz
83 38 Eric Allman
#### Entrance Lobby
84 1 Ken Lutz
85 44 Nitesh Mor
* Swarm Lab Inside Entrance Lobby
86 44 Nitesh Mor
* Blink C0:98:E5:90:00:0B
87 44 Nitesh Mor
* BLEE C0:98:E5:30:00:0A
88 33 Ken Lutz
89 38 Eric Allman
#### Office 490B
90 1 Ken Lutz
91 45 Nitesh Mor
* UHKBBB002.eecs.berkeley.edu
92 45 Nitesh Mor
93 1 Ken Lutz
#### 4th floor Elevator Lobby
94 1 Ken Lutz
95 45 Nitesh Mor
* Blink C0:98:E5:90:00:91
96 45 Nitesh Mor
* SwarmBox swarmnuc1020.eecs.berkeley.edu
97 45 Nitesh Mor
98 1 Ken Lutz
#### Exit Stair Door near 490
99 11 Ken Lutz
100 45 Nitesh Mor
* Blink C0:98:E5:90:00:19
101 2 Ken Lutz
102 45 Nitesh Mor
103 2 Ken Lutz
**Operational Notes**
104 45 Nitesh Mor
- 7/12/16 2:59PM, powerblade on Speaker camera disconnected for inspection and reconnected. Note that accumulated energy goes to zero at this time. 
105 45 Nitesh Mor
- 7/13/16 10AM, powerblade on Immersion room primary projector re-installed, now in correct orientation. Readings from 10am on look correct.
106 45 Nitesh Mor
- 7/14/16 9:22:58AM - Introduced an anomaly by heating the Immersion room BLEE located on the rear pillar with a hot air gun for about 4 min. Temperature and humidity impacted.
107 45 Nitesh Mor
- 7/14/16 9:46AM - Speaker camera was left on since 7/12 2:26pm. Turned off at 7/14 9:46AM
108 45 Nitesh Mor
- 7/15/16 - 9:40AM Primary projector powerblade seems to have a loose connection. No readings from 7/14 3:23PM until re-seated at 7/15 9:40AM
109 45 Nitesh Mor
- 7/18/16 - 11:30AM BLEES installed on conference table chairs w/ new batteries
110 45 Nitesh Mor
- 7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
111 45 Nitesh Mor
- 7/19/16: Beaglebone gateway is got powered off. Last data collected was around 4:56PM. Restarted at 10:50PM
112 45 Nitesh Mor
- 7/20/16: Rear Camera pillar BLEE - Battery replaced 3:26PM
113 45 Nitesh Mor
- 7/26/16 Main projector power blade failed - replaced with new unit (new MAC)
114 45 Nitesh Mor
- 8/1/16 BBB001 down for maintenance
115 45 Nitesh Mor
- 8/8/16 Batteries replaced in all sensors except chairs
116 38 Eric Allman
117 38 Eric Allman
### Jacobs Hall
118 31 Ken Lutz
**Gateways**
119 27 Ken Lutz
~~ML-100 - swarmnuc1005.eecs.berkeley.edu B8:AE:ED:74:09:3D was port 10D-120C-03F10-D room 120~~
120 5 Ken Lutz
BBB - uhkbbb005.eecs.berkeley.edu port 10D-332-04F17-D Room 332
121 19 Ken Lutz
BBB uhkbbb006.eecs.berkeley.edu 54:4a:16:e0:8b:a1 10D-120C-03F10-D room 120
122 19 Ken Lutz
BBB uhkbbb007.eecs.berkeley.edu  6c:ec:eb:5c:64:5b Room 10 10D-10B-02f16-D
123 38 Eric Allman
124 1 Ken Lutz
#### Room 110
125 1 Ken Lutz
**Powerblades**
126 1 Ken Lutz
c0:98:e5:70:01:13 Type A 3D printer 10026	room 110
127 1 Ken Lutz
c0:98:e5:70:01:22
128 1 Ken Lutz
c0:98:e5:70:01:23 Type A 3D printer 10047	room 110
129 1 Ken Lutz
c0:98:e5:70:01:25
130 1 Ken Lutz
c0:98:e5:70:01:26 Laser 2                                room 110C
131 1 Ken Lutz
c0:98:e5:70:01:27 Type A 3D printer 10097	room 110
132 19 Ken Lutz
c0:98:e5:70:01:29 Type A 3D printer 10213	room 110
133 19 Ken Lutz
c0:98:e5:70:00:e2 Laser 1	                                room 110C
134 19 Ken Lutz
c0:98:e5:70:00:e5 Type A 3D printer 10035	room 110
135 19 Ken Lutz
c0:98:e5:70:00:d3 Type A 3D printer 10098	room 110
136 19 Ken Lutz
c0:98:e5:70:00:d7 Type A 3D printer 10025	room 110
137 19 Ken Lutz
c0:98:e5:70:00:f7 Type A 3D printer 10038	room 110
138 19 Ken Lutz
c0:98:e5:70:00:db - Type A 3D printer 10094 room 110
139 38 Eric Allman
c0:98:e5:70:01:31 Type A 3D printer 10034	room 110	
140 38 Eric Allman
141 1 Ken Lutz
**BLEE**
142 34 Ken Lutz
c0:98:e5:30:00:57 room 110 by thermostst
143 19 Ken Lutz
c0:98:e5:30:00:55  check placement in room
144 34 Ken Lutz
145 38 Eric Allman
146 19 Ken Lutz
#### Room 332
147 19 Ken Lutz
148 18 Ken Lutz
**PowerBlades**
149 1 Ken Lutz
c0:98:e5:70:00:8a Carbon 3D printer              room 332
150 4 Ken Lutz
c0:98:e5:70:01:0c Dimension 2 (Bonnie)	room 332
151 19 Ken Lutz
c0:98:e5:70:01:2e Dimension 1 (Clyde)         room 332
152 1 Ken Lutz
153 32 Ken Lutz
**BLEE**
154 1 Ken Lutz
155 19 Ken Lutz
c0:98:e5:30:00:55 room 120
156 32 Ken Lutz
c0:98:e5:30:00:50 room 332 Fortus 380 air exhaust vent
157 32 Ken Lutz
c0:98:e5:30:00:51 room 332 center of room
158 4 Ken Lutz
159 32 Ken Lutz
**Blink**
160 19 Ken Lutz
c0:98:e5:90:00:85 room 332
161 4 Ken Lutz
c0:98:e5:90:00:94
162 19 Ken Lutz
c0:98:e5:90:00:87
163 38 Eric Allman
164 1 Ken Lutz
#### Room 10C
165 19 Ken Lutz
**Blink**
166 34 Ken Lutz
c0:98:e5:90:00:81 - wood shop room 10C
167 34 Ken Lutz
**BLEE**
168 4 Ken Lutz
c0:98:e5:30:00:62 room 10C Woodshop
169 4 Ken Lutz
170 2 Ken Lutz
171 37 Ken Lutz
**Operational Notes**
172 30 Eric Allman
Sensors installed, new batteries 7/15/16
173 30 Eric Allman
174 30 Eric Allman
### Unassigned BBB Ready for deployment
175 30 Eric Allman
UHKBBB008.eecs.berkeley.edu  b0:d5:cc:83:0b:01
176 1 Ken Lutz
UHKBBB009.eecs.berkeley.edu  88:c2:55:83:6c:29