Wiki » History » Version 54
Version 53 (Syed Hasnain, 09/09/2016 01:32 PM) → Version 54/84 (Syed Hasnain, 09/09/2016 01:38 PM)
{{toc}}
# GDP Deployment Notes
## Data users email list created
If you would like to be notified of data anomalies or changes in the sensor actuator send an email to lutz@berkeley.edu asking to be added to the email list, swarm-gdp-data-users@lists.eecs.berkeley.edu
## Conventions
Unless otherwise noted, the name of the corresponding logs are derived from the physical location (currently `bwrc` or `swarmlab`) and the lowercase MAC address:
edu.berkeley.eecs.<location>.device.<mac-addr>
For example, a sensor with MAC address `C0:98:E5:30:00:03` in the immersion room (which is in swarmlab) will be named `edu.berkeley.eecs.swarmlab.device.c098e5300003`
## Provisioning
See [[Provisioning Sensors]] for instructions on how to add new sensors.
## Configuring Gateways
See [[Configuring Gateways]] for information about setting up gateway hosts (typically either BBBs or SwarmBoxes).
## Deployments
### BWRC Server Room
**Sensors and Gateways**
* BBB - UHKBBB004.eecs.berkeley.edu 128.32.63.176
* Rear Wall BLEE - C0:98:E5:30:00:36
* Mid Wall BLEE - C0:98:E5:30:00:5D
* Hot Aisle BLEE- C0:98:E5:30:00:54
* Lab Rear Wall BLEE - C0:98:E5:30:00:09
* BLINK - C0:98:E5:90:00:1E
* Power Blade - Utility power to sump pump - C0:98:E5:70:00:8F
* Power Blade - Utility power to Air Compressor - C0:98:E5:70:00::90
* USB Microphone - mounted on BBB
### BWRC Office Area
#### Sensors and Gateways
* Swarmnuc1002.eecs.berkeley.edu
* BLEE
- Main seating area - C0:98:E5:30:00:A5
- Conference Room , Rabaey Room - C0:98:E5:30:00:A3
- Admin Office - C0:98:E5:30:00:A4
- Conference Room - Brodersen room - C0:98:E5:30:00:A2
- Ken's Office - C0:98:E5:30:00:A1
- Brian Office above thermostat - C0:98:E5:30:00:A0
- Center of student seating area, above thermostat - C0:98:E5:30:00:37
* Blink
- Brodersen Conference Room C0:98:E5:90:00:87
- Rabaey Conference room - C0:98:E5:30:00:94
**Operational Notes**
* 6-17-16 2:59PM Repaired broken Blink in server room. Was reading all zero, now detecting movement correctly.
* 7/11/16 Fixed powerblade on air compressor - was installed backward. Data collected after 7/11 looks correct. Prior was in error. Note that energy accumulated goes to zero when powerblade was disconnected for inspection. Good marker.
* 7/14/16 9:29AM Correlated spike in temperature and humidity for a short period of time across all BLEES in the server room. Probably related to someone working in the room and having propped the door open.
* 7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
* 7/19/16 4:05 PM - 4:19PM: Put a cover over the Lab Rear wall BLEE causing the light level to go to zero. Temp and humidity are down as well.
* 7/19/16 4:20PM - 4:31PM: Put a cover over BLEE in server room, mid wall. Light level goes to zero, temp goes up. Other sensors in the server room do not show similar readings
* 7/25/16 - Added sensors and gateway to BWRC office area. New batteries
* 8/1/16 BBB004 down for maintenance 2-5pm.
* 8/8/2016 Replaced batteries in server room and Kens office
* 8/8/16 Removed test powerblade from air compressor outlet strip
* 8/26/16 9:40AM - 10:10am covered light sensor on BLEE in Ken's office - C0:98:E5:30:00:A1
* 8/26/16 11:42 - Covered light sensor on BLEE Center of student seating area, above thermostat - C0:98:E5:30:00:37
* 8/26/16 12:30 -12:45 (approx) increased humidity on BLEE Brian Office above thermostat - C0:98:E5:30:00:A0
* 8/26/16 2:41-2:47pm increased humidity on Rear Wall BLEE - C0:98:E5:30:00:36
### Cory Hall Swarm Lab and Immersion Room
**Servers and Sensors**
#### Immersion Room
* Primary projector PowerBlade ~~C0:98:E5:70:00:2B~~ C0:98:E5:70:00:8D
* Secondary projector PowerBlade C0:98:E5:70:00:8B
* Speaker Camera PowerBlade C0:98:E5:70:00:8E
* Audience Camera PowerBlade C0:98:E5:70:00:88
* BLEE, rear camera pillar C0:98:E5:30:00:03
* Front wall adjacent to screen Blink C0:98:E5:90:00:0A
* UHKBBB001.eecs.berkeley.edu 128.32.33.236
Chair BLEES C0:98:E5:30:0: {58, 5c, 5F, 7a, 7b, 74, 75, 76, 77, 78}
#### Entrance Lobby
* Swarm Lab Inside Entrance Lobby
* Blink C0:98:E5:90:00:0B
* BLEE C0:98:E5:30:00:0A
#### Office 490B
* UHKBBB002.eecs.berkeley.edu
#### 4th floor Elevator Lobby
* Blink C0:98:E5:90:00:91
* SwarmBox swarmnuc1020.eecs.berkeley.edu
#### Exit Stair Door near 490
* Blink C0:98:E5:90:00:19
**Operational Notes**
- 7/12/16 2:59PM, powerblade on Speaker camera disconnected for inspection and reconnected. Note that accumulated energy goes to zero at this time.
- 7/13/16 10AM, powerblade on Immersion room primary projector re-installed, now in correct orientation. Readings from 10am on look correct.
- 7/14/16 9:22:58AM - Introduced an anomaly by heating the Immersion room BLEE located on the rear pillar with a hot air gun for about 4 min. Temperature and humidity impacted.
- 7/14/16 9:46AM - Speaker camera was left on since 7/12 2:26pm. Turned off at 7/14 9:46AM
- 7/15/16 - 9:40AM Primary projector powerblade seems to have a loose connection. No readings from 7/14 3:23PM until re-seated at 7/15 9:40AM
- 7/18/16 - 11:30AM BLEES installed on conference table chairs w/ new batteries
- 7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
- 7/19/16: Beaglebone gateway is got powered off. Last data collected was around 4:56PM. Restarted at 10:50PM
- 7/20/16: Rear Camera pillar BLEE - Battery replaced 3:26PM
- 7/26/16 Main projector power blade failed - replaced with new unit (new MAC)
- 8/1/16 BBB001 down for maintenance
- 8/8/16 Batteries replaced in all sensors except chairs
### Jacobs Hall
**Gateways**
- ~~ML-100 - swarmnuc1005.eecs.berkeley.edu B8:AE:ED:74:09:3D was port 10D-120C-03F10-D room 120~~
- BBB - uhkbbb005.eecs.berkeley.edu port 10D-332-04F17-D Room 332
- BBB uhkbbb006.eecs.berkeley.edu 54:4a:16:e0:8b:a1 10D-120C-03F10-D room 120
- BBB uhkbbb007.eecs.berkeley.edu 6c:ec:eb:5c:64:5b Room 10 10D-10B-02f16-D
#### Room 110
**Powerblades**
- c0:98:e5:70:01:13 Type A 3D printer 10026 room 110
- c0:98:e5:70:01:22
- c0:98:e5:70:01:23 Type A 3D printer 10047 room 110
- c0:98:e5:70:01:25
- c0:98:e5:70:01:26 Laser 2 room 110C
- c0:98:e5:70:01:27 Type A 3D printer 10097 room 110
- c0:98:e5:70:01:29 Type A 3D printer 10213 room 110
- c0:98:e5:70:00:e2 Laser 1 room 110C
- c0:98:e5:70:00:e5 Type A 3D printer 10035 room 110
- c0:98:e5:70:00:d3 Type A 3D printer 10098 room 110
- c0:98:e5:70:00:d7 Type A 3D printer 10025 room 110
- c0:98:e5:70:00:f7 Type A 3D printer 10038 room 110
- c0:98:e5:70:00:db - Type A 3D printer 10094 room 110
- c0:98:e5:70:01:31 Type A 3D printer 10034 room 110
**BLEE**
- c0:98:e5:30:00:57 room 110 by thermostst
- c0:98:e5:30:00:55 check placement in room
#### Room 332
**PowerBlades**
- c0:98:e5:70:00:8a Carbon 3D printer room 332
- c0:98:e5:70:01:0c Dimension 2 (Bonnie) room 332
- c0:98:e5:70:01:2e Dimension 1 (Clyde) room 332
**BLEE**
- c0:98:e5:30:00:55 room 120
- c0:98:e5:30:00:50 room 332 Fortus 380 air exhaust vent
- c0:98:e5:30:00:51 room 332 center of room
**Blink**
- c0:98:e5:90:00:85 room 332
- c0:98:e5:90:00:94
- c0:98:e5:90:00:87
#### Room 10C
**Blink**
- c0:98:e5:90:00:81 - wood shop room 10C
**BLEE**
- c0:98:e5:30:00:62 room 10C Woodshop
**Operational Notes**
- Sensors installed, new batteries 7/15/16
## TAMU
edu.tamu.esp.Setup1c.device.* edu.esp.tamu.Setup1c.device.*
**BLEE**
c098e530001d
**Blink**
c098e590010
c098e590011
c098e590012
c098e5900ac
**PowerBlade**
c098e5700028
c098e57000c4
c098e57000a8
**Notes**
The sensors have been places in graduate office space. The power blades are connected to power cords in use by students.
### Unassigned BBB Ready for deployment
UHKBBB008.eecs.berkeley.edu b0:d5:cc:83:0b:01
UHKBBB009.eecs.berkeley.edu 88:c2:55:83:6c:29
# GDP Deployment Notes
## Data users email list created
If you would like to be notified of data anomalies or changes in the sensor actuator send an email to lutz@berkeley.edu asking to be added to the email list, swarm-gdp-data-users@lists.eecs.berkeley.edu
## Conventions
Unless otherwise noted, the name of the corresponding logs are derived from the physical location (currently `bwrc` or `swarmlab`) and the lowercase MAC address:
edu.berkeley.eecs.<location>.device.<mac-addr>
For example, a sensor with MAC address `C0:98:E5:30:00:03` in the immersion room (which is in swarmlab) will be named `edu.berkeley.eecs.swarmlab.device.c098e5300003`
## Provisioning
See [[Provisioning Sensors]] for instructions on how to add new sensors.
## Configuring Gateways
See [[Configuring Gateways]] for information about setting up gateway hosts (typically either BBBs or SwarmBoxes).
## Deployments
### BWRC Server Room
**Sensors and Gateways**
* BBB - UHKBBB004.eecs.berkeley.edu 128.32.63.176
* Rear Wall BLEE - C0:98:E5:30:00:36
* Mid Wall BLEE - C0:98:E5:30:00:5D
* Hot Aisle BLEE- C0:98:E5:30:00:54
* Lab Rear Wall BLEE - C0:98:E5:30:00:09
* BLINK - C0:98:E5:90:00:1E
* Power Blade - Utility power to sump pump - C0:98:E5:70:00:8F
* Power Blade - Utility power to Air Compressor - C0:98:E5:70:00::90
* USB Microphone - mounted on BBB
### BWRC Office Area
#### Sensors and Gateways
* Swarmnuc1002.eecs.berkeley.edu
* BLEE
- Main seating area - C0:98:E5:30:00:A5
- Conference Room , Rabaey Room - C0:98:E5:30:00:A3
- Admin Office - C0:98:E5:30:00:A4
- Conference Room - Brodersen room - C0:98:E5:30:00:A2
- Ken's Office - C0:98:E5:30:00:A1
- Brian Office above thermostat - C0:98:E5:30:00:A0
- Center of student seating area, above thermostat - C0:98:E5:30:00:37
* Blink
- Brodersen Conference Room C0:98:E5:90:00:87
- Rabaey Conference room - C0:98:E5:30:00:94
**Operational Notes**
* 6-17-16 2:59PM Repaired broken Blink in server room. Was reading all zero, now detecting movement correctly.
* 7/11/16 Fixed powerblade on air compressor - was installed backward. Data collected after 7/11 looks correct. Prior was in error. Note that energy accumulated goes to zero when powerblade was disconnected for inspection. Good marker.
* 7/14/16 9:29AM Correlated spike in temperature and humidity for a short period of time across all BLEES in the server room. Probably related to someone working in the room and having propped the door open.
* 7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
* 7/19/16 4:05 PM - 4:19PM: Put a cover over the Lab Rear wall BLEE causing the light level to go to zero. Temp and humidity are down as well.
* 7/19/16 4:20PM - 4:31PM: Put a cover over BLEE in server room, mid wall. Light level goes to zero, temp goes up. Other sensors in the server room do not show similar readings
* 7/25/16 - Added sensors and gateway to BWRC office area. New batteries
* 8/1/16 BBB004 down for maintenance 2-5pm.
* 8/8/2016 Replaced batteries in server room and Kens office
* 8/8/16 Removed test powerblade from air compressor outlet strip
* 8/26/16 9:40AM - 10:10am covered light sensor on BLEE in Ken's office - C0:98:E5:30:00:A1
* 8/26/16 11:42 - Covered light sensor on BLEE Center of student seating area, above thermostat - C0:98:E5:30:00:37
* 8/26/16 12:30 -12:45 (approx) increased humidity on BLEE Brian Office above thermostat - C0:98:E5:30:00:A0
* 8/26/16 2:41-2:47pm increased humidity on Rear Wall BLEE - C0:98:E5:30:00:36
### Cory Hall Swarm Lab and Immersion Room
**Servers and Sensors**
#### Immersion Room
* Primary projector PowerBlade ~~C0:98:E5:70:00:2B~~ C0:98:E5:70:00:8D
* Secondary projector PowerBlade C0:98:E5:70:00:8B
* Speaker Camera PowerBlade C0:98:E5:70:00:8E
* Audience Camera PowerBlade C0:98:E5:70:00:88
* BLEE, rear camera pillar C0:98:E5:30:00:03
* Front wall adjacent to screen Blink C0:98:E5:90:00:0A
* UHKBBB001.eecs.berkeley.edu 128.32.33.236
Chair BLEES C0:98:E5:30:0: {58, 5c, 5F, 7a, 7b, 74, 75, 76, 77, 78}
#### Entrance Lobby
* Swarm Lab Inside Entrance Lobby
* Blink C0:98:E5:90:00:0B
* BLEE C0:98:E5:30:00:0A
#### Office 490B
* UHKBBB002.eecs.berkeley.edu
#### 4th floor Elevator Lobby
* Blink C0:98:E5:90:00:91
* SwarmBox swarmnuc1020.eecs.berkeley.edu
#### Exit Stair Door near 490
* Blink C0:98:E5:90:00:19
**Operational Notes**
- 7/12/16 2:59PM, powerblade on Speaker camera disconnected for inspection and reconnected. Note that accumulated energy goes to zero at this time.
- 7/13/16 10AM, powerblade on Immersion room primary projector re-installed, now in correct orientation. Readings from 10am on look correct.
- 7/14/16 9:22:58AM - Introduced an anomaly by heating the Immersion room BLEE located on the rear pillar with a hot air gun for about 4 min. Temperature and humidity impacted.
- 7/14/16 9:46AM - Speaker camera was left on since 7/12 2:26pm. Turned off at 7/14 9:46AM
- 7/15/16 - 9:40AM Primary projector powerblade seems to have a loose connection. No readings from 7/14 3:23PM until re-seated at 7/15 9:40AM
- 7/18/16 - 11:30AM BLEES installed on conference table chairs w/ new batteries
- 7/17/16-7/19/16: Missed about 2 days worth of data due to bug in the MQTT-gateway.
- 7/19/16: Beaglebone gateway is got powered off. Last data collected was around 4:56PM. Restarted at 10:50PM
- 7/20/16: Rear Camera pillar BLEE - Battery replaced 3:26PM
- 7/26/16 Main projector power blade failed - replaced with new unit (new MAC)
- 8/1/16 BBB001 down for maintenance
- 8/8/16 Batteries replaced in all sensors except chairs
### Jacobs Hall
**Gateways**
- ~~ML-100 - swarmnuc1005.eecs.berkeley.edu B8:AE:ED:74:09:3D was port 10D-120C-03F10-D room 120~~
- BBB - uhkbbb005.eecs.berkeley.edu port 10D-332-04F17-D Room 332
- BBB uhkbbb006.eecs.berkeley.edu 54:4a:16:e0:8b:a1 10D-120C-03F10-D room 120
- BBB uhkbbb007.eecs.berkeley.edu 6c:ec:eb:5c:64:5b Room 10 10D-10B-02f16-D
#### Room 110
**Powerblades**
- c0:98:e5:70:01:13 Type A 3D printer 10026 room 110
- c0:98:e5:70:01:22
- c0:98:e5:70:01:23 Type A 3D printer 10047 room 110
- c0:98:e5:70:01:25
- c0:98:e5:70:01:26 Laser 2 room 110C
- c0:98:e5:70:01:27 Type A 3D printer 10097 room 110
- c0:98:e5:70:01:29 Type A 3D printer 10213 room 110
- c0:98:e5:70:00:e2 Laser 1 room 110C
- c0:98:e5:70:00:e5 Type A 3D printer 10035 room 110
- c0:98:e5:70:00:d3 Type A 3D printer 10098 room 110
- c0:98:e5:70:00:d7 Type A 3D printer 10025 room 110
- c0:98:e5:70:00:f7 Type A 3D printer 10038 room 110
- c0:98:e5:70:00:db - Type A 3D printer 10094 room 110
- c0:98:e5:70:01:31 Type A 3D printer 10034 room 110
**BLEE**
- c0:98:e5:30:00:57 room 110 by thermostst
- c0:98:e5:30:00:55 check placement in room
#### Room 332
**PowerBlades**
- c0:98:e5:70:00:8a Carbon 3D printer room 332
- c0:98:e5:70:01:0c Dimension 2 (Bonnie) room 332
- c0:98:e5:70:01:2e Dimension 1 (Clyde) room 332
**BLEE**
- c0:98:e5:30:00:55 room 120
- c0:98:e5:30:00:50 room 332 Fortus 380 air exhaust vent
- c0:98:e5:30:00:51 room 332 center of room
**Blink**
- c0:98:e5:90:00:85 room 332
- c0:98:e5:90:00:94
- c0:98:e5:90:00:87
#### Room 10C
**Blink**
- c0:98:e5:90:00:81 - wood shop room 10C
**BLEE**
- c0:98:e5:30:00:62 room 10C Woodshop
**Operational Notes**
- Sensors installed, new batteries 7/15/16
## TAMU
edu.tamu.esp.Setup1c.device.* edu.esp.tamu.Setup1c.device.*
**BLEE**
c098e530001d
**Blink**
c098e590010
c098e590011
c098e590012
c098e5900ac
**PowerBlade**
c098e5700028
c098e57000c4
c098e57000a8
**Notes**
The sensors have been places in graduate office space. The power blades are connected to power cords in use by students.
### Unassigned BBB Ready for deployment
UHKBBB008.eecs.berkeley.edu b0:d5:cc:83:0b:01
UHKBBB009.eecs.berkeley.edu 88:c2:55:83:6c:29